Reasons Your fiat 500x key fob 500 Key Fob Won't Work

A key fob for the fiat 500 replacement key near me 500 is a handy way to open the doors and start the car. However, there are numerous reasons why the key fob might stop working. These include a dead coin battery damage to the receiver module, water issues, or interference.

This listing is for an NEW replacement fiat key fob replacement Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths in the automotive industry). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob being inoperative. Modern key fobs have limited operating range and must be within a few inches of the vehicle to function. If you are far from your vehicle and you press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) by a new one from a reputable brand like Panasonic, Duracell, or Energizer. They can be found in the local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while you're standing close to your fiat 500 remote key programming 500. The car will blink its parking lights and the key fob should work the lock and unlock switches.

If the key fob won't work after replacing the battery, it might be damaged by water that blocks it from connecting to the receiver module in your car. Water damage can happen in many ways, such as simply splashing or submerging the key fob saltwater at the beach. If you suspect that your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If that doesn't work your fob may need to be reprogrammed by a professional auto locksmith or by the dealer.

Water Damage

Water damage can occur when you immerse the fob in the ocean, or wash it in a washer. Saltwater can cause the circuit board to short, and eventually fail. It's not a good thing to get the fob wet, but don't give it up in the event that you accidentally drop it in the water or don't take it out of your pocket.

Take the battery off first. Clean the electronic chip using isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Test the fob next to see if it is functioning. If the fob doesn't work, it may need to be reset. This is usually handled by a dealer or professional auto locksmith.

If the key is more recent and has not been programmed to your vehicle it is likely to need to be replaced completely. This is a simple procedure that can be carried out by a professional locksmith for automotive use. The locksmith will need the key to be cut to match your car's ignition. The locksmith will also need to program your fob into the car's system. This is an affordable and quick procedure that can be completed in the same day.

Receiver Module Issues

One of the simplest reasons your 500 key fob could stop functioning is that it's out of range. The remote has a range of 30 feet. So if you are too far from your car it will not respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.

If you've replaced the coin battery (commonly known as"button" or "button" or "watch") and the fob isn't working It could be because of an internal circuit board issue. Reprogramming the fob is usually the solution to this problem. You can find directions on how to do this for the majority of vehicles by searching YouTube or looking through the owner's manual.

It could be necessary to replace the clips made of metal that hold the coin batteries in place. If they loose tension, it may prevent your battery from sitting properly and cause your remote to malfunction.

In rare cases the fob could be out of the vehicle's sync because of hardware or software issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain situations they might need to reinstall the program in your body control module too.

Interference

In addition to a dead battery on a coin the key fob could not be able to receive or transmit a signal due to interference. This can occur when the keyfob is located in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob may not work due to a poor connection with the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands that are then translated by the vehicle.

There is a straightforward method to reset the 500's onboard system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computers, which could help get your key fob working again. If the problem persists you should speak with an expert technician. They can identify the root cause of any problems.